Isys iTerra TL1290 Color LED Printer User Manual

www.isys‐group.com iTerraTL1290UserGuide iSys - The Imaging Systems Group Inc. © Copyright 2009 

8 STEP 18 STEP 19 1. Insert the power cable. 2. Turn the printer ON. In order to reduce electromagnetic interference—”noise” that interfere

9 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP 10

10 Replacing the Fuser STEP 1 STEP 2 CAUTION: The Fuser may be hot. Lift the Blue tab up to unlock the fuser. Using the handle, gently Lif

11STEP 3 STEP 4 Remove the four image drums/toner cartridge units and place them on a flat surface. Cover them with dark paper or plastic t

12STEP 9 STEP 10 Put the image drum/toner cartridge units back into the printer. 1. Close the top cover. 2. Turn the Printer on. Replaci

13Loading the printer on the feeder STEP 1 To properly align the pins with the printer, align the printer flush with the back and left sides

14Loading Paper into the Cart STEP 1 STEP 2 The image above shows the black sliders Set the black sliders to the correct paper width.

15STEP 5 STEP 6 Gently pull the paper downwards and feed the paper underneath the orange roller. Open the Plexiglas paper loading door , an

16 STEP 9 STEP 10 To load the paper, press the load button on the cart menu Open the cutter door and while using caution, carefully remov

17 Menu Options Media Management Media Type – Selecting this allows you to change the media type. You may choose from 6 options: Media Type 1.

Table of Contents Ordering Consumable Supplies 2 Safety Information 3 120-Volt Models 3 220/240-Volt Models

18 Adjustments TOF Sensor – allows you to adjust the sensor when troubleshooting. Your printer has been configured at the factory to sense low bl

19Printer Menu Summary Configuration • Page Count, Supplies Life • Network and System Settings, etc. Print Information• Printer & Network Conf

20• Down-arrow button Enters menu mode and enables downward movement through the displayed list of menu items • Back button Returns to the previo

21• Administrator menu: accessed by pressing the Enter button for more than 2 seconds while turning on the printer power supply (including Restar

22Maintenance Cleaning the LED Heads Clean the LED heads: • Any time you replace a toner cartridge • If printing is showing signs of faded images,

23 Remove Tray 1 from the printer. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly

24Errors 1 to 9 – Emergency Stop, Control PCB Internal Errors If the cart menu displays errors 10 to 19 ensure that all doors on the cart are clos

25STEP 3 STEP 4 Printer Side Cover STEP 1 STEP 2 STEP 3 STEP 4

26 Printer Top Cover STEP 1 STEP 2 WARNING: Be careful not to touch the fuser unit which may be hot after printing. If the fuser unit is hot, w

27 STEP 7 STEP 8 STEP 9 STEP 10 STEP 11 Avoiding Paper Jams The following table summarizes possible causes of paper jams and suggests w

1 iSys is an ISO 9001 Registered Firm Thank you for selecting the iTerra TL1290. iSys will make every effort to assist you with operation of your

28Your print media is creased or curled. Use appropriate media. Decurled media can be used. Your print media sheets are not aligned with each oth

29Interfaces The iTerra TL1290 has three interface options, USB, Centronics, and network. Network 1. Enter the printer Menu. 2. Scroll down t

30STEP 2 Select Add a Printer on the Left hand side of the window h Press Next STEP 3 Welcome to the Add Printer Wizard h Press Next

31STEP 4 Select Local printer attached to this computer h Press Next STEP 5 Select Create a new port: Type of port h Standard TCP/IP Port h Pre

32STEP 6 Welcome to the Add Standard TCP/IP Printer Port Wizard h Press Next STEP 7 Enter the printers IP Address into the box h Press Next

33STEP 8 Under Device Type h Select Standard h Generic Network Card h Press Next STEP 9 Completing the Add Standard TCP/IP Printer Port Wizard

34STEP 10 Select Have Disk STEP 11 Select Browse h Locate and select the TL1290 Driver h Press Ok h Press Next

35STEP 12 Select the iSys iTerra TL1290 Printer h Press Next STEP 13 Enter the printer name h Select yes if you would like the iSys iTerra TL12

36 STEP 14 Select a sharing option h Press Next STEP 15 Enter a location and a comment h Press Next

37 STEP 16 Select Yes or No to print a test page h press Next STEP 17 Completing the Add Printer Wizard h press Finish

2 Ordering Consumable Supplies Using non-Qualified TL1290 media and consumables will void the printers’ warranty. • Reach iSys toll-free by pho

38 STEP 18 If this message appears after installing the driver h Select Continue Anyway Warnings and Precautions Cutter Blade TL1290 Printer

39Printer and Feeder Cable CAUTION: Turn the printer off before (dis)connecting the cable between printer and feeder. Failure to do so may result

40 Limitation of Liability The Imaging Systems Group’s total liability to the purchaser, or to any third party, for damages from any and all cause

41 Material Safety Data Sheet Emergency First Aid Procedures Toner inhaled. Remove person to fresh air. If necessary, seek medical attention. T

42iTerra TL1290 Warranty iSys - The Imaging Systems Group Inc. (iSys) warrants the TL1290 (Product) to be free from defects in materials and work

3 Safety Information 120-Volt Models Your iSys product has been carefully designed to give you years of safe, reliable performance. As with all e

4you have a suitable power supply before connecting the product. If in doubt contact your dealer or check with your local power provider. Ensure

5Unpacking and Installation Check components: (1) Printer, (2) Light-shield bags, paper tray media labels, LED lens cleaning pad, (3) Power Cable

6STEP 6 STEP 7 Remove colored image drum packing pieces. Remove tape STEP 8 STEP 9 Remove protective sheet 1. Remove colored lock

7STEP 12 STEP 13 1. Lock toner cartridge with colored lever. 2. Repeat these steps for remaining toner cartridges. Close the top cover. S