Isys i36 User Manual

i36 ImageMasterUser Guidei36 ImageMaster is a product of iSys - The Imagaing Systems Group. © 2005

i36 ImageMaster User Guide 114INSTALLING THE PRINT DRIVERSpicer Docu-Jet Install StepsThe following screen shots are from Windows 2000. These screens

12 i36 ImageMaster User Guide4Figure 4.Figure 5.

i36 ImageMaster User Guide 13Figure 6.4Figure 7.

14 i36 ImageMaster User GuideFigure 8.Figure 9.4

i36 ImageMaster User Guide 154The appropriate port for TCP/IP printing can be selected here if Jet admin hasalready been setup for the i36.Figure 10.F

16 i36 ImageMaster User Guide4Figure 12If HP jet admin is installed make sure the correct Port is selected. It should reflect theport name given to th

i36 ImageMaster User Guide 174You can enter any company name. The two important pieces of information thatmust be exact are the serial number and the

18 i36 ImageMaster User Guide5QUICKDRAW MEDIA INSTALLATIONCAUTION: Do not touch the thermal print head. Natural body oils candamage the print head. Sc

i36 ImageMaster User Guide 195Figure 15. Media Path.To install a replacement media roll, open lid assembly as described on page 181. Replace media cor

20 i36 ImageMaster User Guide6. Thread the media as shown in figure 15. Allow an extra few inches of media through the exit path, past the cutter a

i36 ImageMaster User Guide 3Thank you for selecting the i36 ImageMaster plotter. The employees and manage-ment at iSys will make every effort to assis

i36 ImageMaster User Guide 216QUICKDRAW MEDIA FOR THE IMAGEMASTERThe iSys QuickDraw line of direct image media is matched to the performancecharacteri

22 i36 ImageMaster User Guide7STARTING THE I36 IMAGEMASTERPlotterTo start the plotter, press the main power (I/O) Switch (see Figure 1 (2)). The plott

i36 ImageMaster User Guide 237During the initializing procedure, the status of these LEDs is as follows:1. The top green LED will remain lighted, indi

24 i36 ImageMaster User Guide8USING THE CONTROL PANEL AND LCD DISPLAYThe control panel of the i36 ImageMaster consists of an LCD display, three indi

i36 ImageMaster User Guide 258Settings changes can only be performed in the “OFF LINE” mode.1. Take the plotter OFFLINE by pressing the ON/OFF LINE ke

26 i36 ImageMaster User Guide8Holding the up or down arrow key while a menu item is selected will scroll throughthe item options until a menu limit ha

i36 ImageMaster User Guide 278User ModeSelects between two user-defined settings. To access functions ineither user mode.- select ON/OFF LINE.- press

28 i36 ImageMaster User Guide8This requires a slower plot speed (see Speed section of guide). Do not use the FILMsetting on any other media other than

i36 ImageMaster User Guide 298End of Transmission (EOT) CutIf enabled, makes the plotter cut the media after it detects a remote end of transmis-sion

30 i36 ImageMaster User Guide9WARRANTY, MAINTENANCE AND SERVICEWarrantyThe iSys written warranty is included with your shipment. Please take the time

4 i36 ImageMaster User GuideContentsUNPACKING ... 6LOCATION OF TH

i36 ImageMaster User Guide 5Scaling ... 28F

6 i36 ImageMaster User Guide1UNPACKINGWARNING: The i36 ImageMaster plotter weighs approximately 70 kg (160 lb),Use appropriate care when unpacking, li

i36 ImageMaster User Guide 72LOCATION OF THE I36 IMAGEMASTERProperly locating the i36 ImageMaster will help to enhance it’s performance andextend it’s

8 i36 ImageMaster User Guide3CABLE CONNECTIONSThe cable connections and power switch on the back of the i36 ImageMaster areshown in Figure 1. They are

i36 ImageMaster User Guide 93AC Power Cable - 220/230 VoltCAUTION: Read the following procedure before connecting to a 220/230 voltpower source. The i

10 i36 ImageMaster User Guide3Connecting to your PC1. Connect the 3 ft. Centronics cable (provided) to connectors 4 and 5 in Figure 1.2. Connect your